ITI CBT Exam Paper 3 September 2021
CBT Exam Paper Analysis
ये प्रश्न 3 September 2021 के CBT परीक्षा में पूछे गये थे |
सभी प्रश्न आईटीआई के छात्र जो 3 September को परीक्षा दें चुकें है उनके द्वारा भेजा गया है |
Electrician Theory
First Year
Q . 1 Which plier is used for making wire hooks and loops?
A Flat nose plier
B Long nose plier
C Round nose plier
D Diagonal cutting plier
Q. 2 Which disposal method of waste save lot of energy?
A Land fill
B Recycling
C Incineration
D Composting
Q. 3 What is the use of mortise chisel?
A General chiselling work in wood
B Making rectangular holes in wood
C Paring and finishing joints in wood
D Light chiselling cleaning sharp corners and in wood
Q. 4Which type of calliper is used to draw parallel lines along the outer edges of the materials?
A Inside calliper
B Jenny calliper
C Outside calliper
D Spring joint calliper
Q. 5 Which file is used for sharpening the blunt teeth of a tenon saw?
A Square file
B Round file
C Triangular file
D Half round file
Q. 6 Which type of curve cutting hand saw is used for internal cutting in wood?
A Compass saw
B Key hole saw
C Coping saw
D Fret saw
Q. 7 What is the unit of insulation resistance?
A Ohm
B Kilo ohm
C Milli ohm
D Mega ohm
Q. 8 What is the effect of electric current on neon lamp?
A Heating effect
B Magnetic effect
C Chemical effect
D Gas ionization effect
Q. 9 What is the effect of the parallel circuit with one branch opened?
A Current will remain same
B Whole circuit will not function
C No current will flow in that branch
D Voltage drop increase in the opened branch
Q. 10 Which material is the paramagnetic substance?
A Cleat wiring
B Copper
C Bismuth
D Graphite
Q. 11 Which type of capacitor is used for space electronics?
A Plastic film type
B Ceramic disc type
C Electrolytic-Aluminum type
D Electrolytic-Tantalum type
Answers :
- C
- B
- B
- B
- C
- B
- D
- D
- C
- B
- D
Second Year
B Right hand palm rule
C Fleming’s left-hand rule
Q. 2 Name the part of DC generator?
A Side end plates
B Pole shoe lamination
C Commutator segment
D Armature core lamination
Q. 3 What is the function of split rings in DC generator?
A Maintain constant voltage
B Collects the current unidirectionally
C Reduces the voltage drop at brushes
D Increases the terminal voltage than rated
Q. 4 What is the effect in D.C generator, if it is kept ideal for long time?
A Field coil resistance increases
B Armature resistance increases
C Increase the armature reaction
D Looses its residual magnetism
Q. 5 What is the name of the symbol?
A Two input OR gate
B Two input AND gate
C Two input NOR gate
D Two input NAND gate
Q. 6 Which cable ties are used to bunch the wires?
A Silk ties
B P.V.C ties
C Nylon ties
D Cotton ties
Q. 7 Which drive is classified according to mode of operation?
A Group drive
B Manual drive
C Individual drive
D Continuous duty drive
Q. 8 What is the name of the component marked as X’ in the block diagram of AC drive?
B D.C bus
C Inverter
D A.C motor
Q. 9 What is the minimum permissible single phase working voltage, if the declared voltage is 240V as per ISI?
A 233 V
B 228 V
C 216 V
D 211 V
Q. 10 What is the full form of PWM?
A Pulse Wide Modulation
B Pulse Width Modulation
C Phase Wide Modulation
D Phase Width Modulation
Q. 11 Which device senses the wind speed in a wind power generation?
A Exciter unit
B Turbine controller
C Chopper controller
D Line controller unit
Q. 12 Which type of line insulator is used at the dead ends of the H.T overhead lines?
A Pin insulator
B Disc insulator
C Stay insulator
D Post insulator
Q. 13 How the rupturing capacity of circuit breaker is rated?
A KV
B KW
C MVA
D KVAR
Q. 14 Which type of relay is used in both A.C and D.C supply?
A Reed relay
B Impulse relay
C Thermal relay
D Clapper-type armature relay
Answer :
- D
- D
- B
- D
- D
- C
- D
- B
- B
- B
- B
- B
- C
- B
Workshop Calculation and Science
First Year
Q. 1 What is the square root of 529?
A : 13
B : 23
C : 33
D : 43
Q. 2 What is the x value for x2 + 62 =102?
A : 4
B : 6
C : 8
D : 10
Q. 3 What is the rate of change of displacement of a body?
A : Body at rest
B : Body at motion
C : Speed
D : Velocity
Q. 4 What is the melting point of aluminium?
A : 660°C
B : 680°C
C : 670°C
D : 620°C
Q. 5 Which is the unit electrical power?
A : Volts
B : Ohms
C : Watts
D : Ampere
Q. 6 How much load is lifted if an effort of 25 kg is applied to a simple machine
having velocity ratio of 4 and efficiency 75%?
A : 65 kg
B : 70 kg
C : 75 kg
D : 80 kg
Answer :
- B
- C
- D
- A
- C
- C
Second Year
instruction
- A
- A
- B
- D
- A
- B
- C
Employability Skills
C mouse and keyboard
should not exceed more than……………
Fitter Theory
First Year
B Lead
C Brass
D Copper
A : Diagonal scale
under water?
during construction?
B : 80 cm
- C
- A
- D
- A
- A
- B
COPA
Q.1 कंप्यूटर किस प्रकार का उपकरण है?
- वैद्युत उपकरण
- इलेक्ट्रॉनिक उपकरण
- इलेक्ट्रो मैग्नेटिक
- इलेक्ट्रो मैकेनिकल
Key : 2
Q.2 Analytical engine का आविष्कार किसने किया?
- चार्ल्स बैबेज
- जॉन लिकरर्ट
- जॉन मौची
- एम वी विल्क्स
Key : 1
Q. 3 सीपीयू की आंतरिक ऊर्जा आपूर्ति इकाई कौन सी है?
A : CVT | सी वी टी
B : UPS | यूपीएस
C : SMPS | एसएमपीएस
D : Stablizer | स्टेबलाइजर
Key : C
Q. 4 Which one is an example for OS? | ओएस के लिए कौन सा उदाहरण है?
A : Antivirus | एंटीवायरस
B : Windows | विंडोज
C : MS Office | एमएस ऑफिस
D : Macromedia | मैक्रोमीडिया
Key : B
Q. 5 Which shortcut key is used to copy and paste a file folder ?
A : Ctrl+ X and Ctrl + V
B : Ctrl + A and Ctrl + V
C : Ctrl + Z and Ctrl + V
D : Ctrl + C and Ctrl + V
Key : D
Q. 6 Where does the pinned application stayed in Windows Os?
A : Desktop | डेस्कटॉप
B : Notification Area | अधिसूचना क्षेत्र
C : Start Button | प्रारंभ करें बटन
D : Task Bar | टास्क बार
Key : D